Fire-lite MS-9200(C)/E Field Software Change Procedure (and Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Fire-lite MS-9200(C)/E Field Software Change Procedure (and herunter. Fire-Lite MS-9200(C)/E Field Software Change Procedure (and programming existing MS-9200 Systems for use with the LCD-40) User Manual Benutzerhandbuch

Document 50053 Rev M 1/10/08 P/N 50053:M 1 of 5

MS-9200(C)/E

Field Software Change Procedure

(and Programming Existing MS-9200

Systems for use with the LCD-40)

Document #50053 Rev. M 1/10/08

ECN 08-019 P/N 50053:M

Firmware Change

This procedure outlines the mechanical installation steps required to install EPROMs in the MS-9200, MS-9200C

and MS-9200E.

Handling precautions for integrated circuits

Static electricity can destroy integrated circuits (ICs)! To prevent damage to the EPROM, a wrist strap and a

static-free IC insertion/extraction tool is highly recommended. The manufacturer cannot be responsible for

damage to the EPROM as a result of improper handling.

System Power Sources

Always remove primary and secondary power before working on the system!

1. Disconnect battery backup power before working on the system!

2. Proceed by disconnecting AC power to the panel at the main service circuit

breaker (not the circuit breaker at the alarm control panel's power supply).

3. Wait 60 seconds to allow for capacitive discharge before touching any of the

system's components.

4. Reverse the procedure for powering up the system - AC first - then batteries.

Pin 1

Notch

Integrated Circuit Pin Conversion

Observe proper orientation of any IC removed or installed! Note location of Pin 1 with respect to the notch in the

body of the IC. The replacement EPROM must be installed in the same manner as the EPROM removed. Failure

to observe this orientation will result in destruction of the EPROM. NOTE: Some ICs may have a small dot instead

of a notch for orientation purposes.

1 2 3 4 5

Inhaltsverzeichnis

Seite 1 - Firmware Change

Document 50053 Rev M 1/10/08 P/N 50053:M 1 of 5MS-9200(C)/EField Software Change Procedure(and Programming Existing MS-9200Systems for use wi

Seite 2 - Programming and Testing

2 of 5Document 50053 Rev M 1/10/08 P/N 50053:MEPROM ReplacementObserve proper orientation of any IC removed or installed! To replace the EPROM,

Seite 3

Document 50053 Rev M 1/10/08 P/N 50053:M 3 of 5LCD-40 installation in an existing MS-9200(C)/EIn an existing MS-9200(C)/E installation, the f

Seite 4 - Software Changes

4 of 5Document 50053 Rev M 1/10/08 P/N 50053:MSoftware ChangesThe following Table summarizes the MS-9200(C) software changes, specifying these

Seite 5

Document 50053 Rev M 1/10/08 P/N 50053:M 5 of 5Software ChangesThe following Table summarizes the MS-9200E software changes, specifying these

Kommentare zu diesen Handbüchern

Keine Kommentare

Fire-lite MS-9200(C)/E Field Software Change Procedure (and Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Fire-lite MS-9200(C)/E Field Software Change Procedure (and herunter. Fire-Lite MS-9200(C)/E Field Software Change Procedure (and programming existing MS-9200 Systems for use with the LCD-40) User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Fire-lite MS-9200(C)/E Field Software Change Procedure (and