Fire-lite LED-10 Series Remote Fire Annunciator Bedienungsanleitung

12 Clintonville Road, Northford, CT 06472BDocument # 5040010/27/97 Revision:P/N 50400:B ECN 97-510The LED-10 SeriesRemote Fire Annunciatorsfor use

10Document 50400 Rev B 10/27/97 P/N 50400:BLED Indicators and Piezo SounderThe LED-10 Series annunciators provide LEDs which indicate the sys

11Document 50400 Rev B 10/27/97 P/N 50400:BLED-10LS2 OnlyZone Alarm - Zones 1 through 8The red LED for Zones 1 through 8 on theLED-10LS2 oper

12Document 50400 Rev B 10/27/97 P/N 50400:BAcknowledgeWhen the Acknowledge switch is pressed andreleased, the LED-10 sends an Acknowledgecomm

13Document 50400 Rev B 10/27/97 P/N 50400:BSection Two: Mounting LED-10 Series AnnunciatorsLED-10 Series Annunciator PreparationThe LED-10 Se

14Document 50400 Rev B 10/27/97 P/N 50400:BSemi-flush Mount BackboxRemove the plug-in terminal blocks from the LED-10 Series circuit board.

15Document 50400 Rev B 10/27/97 P/N 50400:BSurface Mount BackboxRemove the plug-in terminal blocks from the LED-10 Series circuit board. Con

16Document 50400 Rev B 10/27/97 P/N 50400:BSection Three: LED-10 Series Electrical ConnectionsThe LED-10 Series Annunciators can be powered b

17Document 50400 Rev B 10/27/97 P/N 50400:BLED-10IMThe LED-10IM Interface Module provides an EIA-485 port to support the LED-10 Series,AFM Se

18Document 50400 Rev B 10/27/97 P/N 50400:BLED-10 SeriesPlug-in terminal blocksNotes:1) All connections are power-limited and supervised.2) A

19Document 50400 Rev B 10/27/97 P/N 50400:BLED-10IMEIA-48524 VDC TB2Terms 1 (+)and 2 (-)MS-5210UDLED-10 Series in grounded boxLED-10 Series i

2Document 50400 Rev B 10/27/97 P/N 50400:B

20Document 50400 Rev B 10/27/97 P/N 50400:BSection Four: EIA-485 Shield TerminationsThe EIA-485 circuit must be wired using a twisted-shielde

21Document 50400 Rev B 10/27/97 P/N 50400:BWhen the EIA-485 shield is in full conduit: The EIA-485 loop allows the FACP tocommunicate with t

22Document 50400 Rev B 10/27/97 P/N 50400:BNotes

23Document 50400 Rev B 10/27/97 P/N 50400:BNote: To ensure the best fit, cut directly along the dotted line surroundingeach label.Slide-In La

24Document 50400 Rev B 10/27/97 P/N 50400:BNotes

25Document 50400 Rev B 10/27/97 P/N 50400:BNotes

26Document 50400 Rev B 10/27/97 P/N 50400:BNotes

27Document 50400 Rev B 10/27/97 P/N 50400:B

28Document 50400 Rev B 10/27/97 P/N 50400:B

3Document 50400 Rev B 10/27/97 P/N 50400:BContentsSection One: LED-10 Series Annunciators ... 4Features...

4Document 50400 Rev B 10/27/97 P/N 50400:BSection One: LED-10 Series AnnunciatorsThe Fire•Lite LED-10 Series Annunciators consist of the LED-

5Document 50400 Rev B 10/27/97 P/N 50400:BLED-10 only:• Function switches for:üAcknowledge üSignal Silence üDrill üSystem Reset• Enable/Disab

6Document 50400 Rev B 10/27/97 P/N 50400:BFigure 1-2: Wiring to TerminalsCurrent Consumption @ 24 VDC nominal (filtered)Normal/Standby (no a

7Document 50400 Rev B 10/27/97 P/N 50400:BSW1 DIP Switch SettingsThe OPEN position on SW1 is the OFF state. Refer to Figure 1-3 for an expla

8Document 50400 Rev B 10/27/97 P/N 50400:BSW2 DIP Switch SettingsSW2 switch settings are as follows:1 - LED-10 Only (not used on LED-10L and

9Document 50400 Rev B 10/27/97 P/N 50400:BADDRESS SWITCH SETTINGS ADDRESS SWITCH SETTINGS1 2 3 4 5 6 1 2 3 4 5 6INVALID 0 0 0 0 0 0 17 0 1 0